Savings verified from real meter readings. No marketing maths.

Hotels · Care homes · Leisure · Offices · Estates

Your plant room is burning money.
We’ll show you how much.

Savings verified from your own meter readings, not marketing maths. The OH4 Energy Saving System fits around the heating and cooling pipework you already have.

V1 Energy Solutions is a UK-based reseller of the OH4 Energy Saving System. The system is manufactured by OH4 Limited.

OH4 sheeting fitted around insulated pipework on a rooftop chiller

What it is

A fitted system.
On the pipes you already have.

The OH4 Energy Saving System is fitted around the heating, hot water and chilled water pipework of closed-loop systems. Your boilers, chillers and controls stay as they are.

  • 16% to 28%Reductions reported across nine published case studies, each with its own measurement period.
  • No downtimeNothing is cut or drained, and your plant keeps running.
  • No electrical connectionNothing is added to the water.

Two published results

The Headland Hotel, Newquay£50,453Saved in year one on heating and hot water.First full 12 months, adjusted for weather and occupancy, at 9.8p per kWh.Read the case study Amica Care, Exmouth House28%Less gas for heating and hot water.A one month measurement: November 2025, weather adjusted.Read the case study

Why it is straightforward

No disruption.
No guesswork.

  • No downtime

    Heating, hot water and cooling keep running while it is fitted.

  • Nothing cut or drained

    It fits around the outside of your existing pipework.

  • No chemicals

    Nothing is added to the water.

  • Measured on your own meters

    You judge the result from your own meter readings.

  • Quick to fit

    Published installations took from under an hour to three hours.

  • Weather adjusted

    Every published result allows for the weather, so a milder year does not distort the result.

How it works

Long story short,
it’s a tape on your pipes.

OH4 uses magnetic sheeting wrapped around the outside of pipework. The system is intended to improve heat transfer. It has no electrical connection and nothing is added to the water.

The installation requires no cutting or draining. Where insulation or cladding is opened for access, it is reinstated around the fitted system. Your plant keeps running.

Insulated and clad chiller pipework before installationBefore

Your pipework as it is

The insulated pipework before installation. Your meters record what your boilers or chillers use today.

OH4 sheeting wrapped around the pipe and secured with tiesBeing fitted

Sheeting around the pipe

The sheeting wraps around the outside of the pipe and is secured in place. Nothing is cut or drained.

Metal cladding refitted around the insulated pipeworkWith OH4

Insulation and cladding back on

The insulation is closed and the cladding refitted. It looks as it did before; your meters show what changes.

See the installation from start to finish

What sets it apart

Built to go on
without getting in the way.

  1. Fits live systems

    Everything keeps running while it goes on. No cutting and no draining.

  2. Nothing in the water

    No chemicals. It sits on the outside of the pipes, with no electrical connection.

  3. Heating and cooling

    For closed-loop heating, hot water and chilled water circuits, served by boilers or chillers.

  4. EcoVadis Gold

    OH4 Limited, the manufacturer, holds an EcoVadis Gold medal. EcoVadis places OH4 in the top 5% of companies it assessed in the 12 months before the medal was issued. It rates how OH4 runs its business, not energy savings, and is valid until September 2027.

    Check the rating on EcoVadis

Savings calculator

What could you
stop wasting?

Move the slider to your yearly heating and cooling spend. The estimate updates as you go.

Gas and electricity for your boilers and chillers, not your whole energy bill.

£150,000 a year

Estimated saving each year
£24,000 to £42,000
Over 10 years
£240,000 to £420,000

Indicative only. The range applies the published case study results, 16% to 28%, to the spend you enter. Every site is different, and your figure is confirmed by a site survey.

Book a 15 minute call (opens Jake’s calendar in a new tab)

Published results

Measured in buildings
like yours.

Each result relates to its own site, loads and measurement period. Read the period before comparing.

All nine case studies

“We were delighted with how non-invasive the installation was, with no disruption experienced to the hotel’s operation”

Richard PalmerDirector, The Headland Hotel
Read the Headland case study

Sector highlights

Hotels and care homes.
Results you can check.

How we start

One building first.
Then let the numbers decide.

  1. 15 minute call

    We talk through your site, your spend and whether it is a fit.

  2. Site survey

    We look at your plant room, pipework and meter data, and estimate what it could save.

  3. Pilot in one building

    Fit one building and follow the result on your own meters.

  4. Wider rollout

    If the numbers stack up, repeat it across the rest of your estate.

Questions people ask

Does it disrupt the building?

No. It fits around existing pipework while the plant keeps running. Nothing is cut or drained, there is no electrical connection and nothing is added to the water.

What does it work on?

Closed-loop heating, hot water and chilled water systems only. It is not for open-loop, single-pass or direct gas heating.

Does it go on every pipe?

No. It goes on clean, straight runs of pipe, chosen at the site survey.

How does it work?

OH4 uses magnetic sheeting wrapped around the outside of pipework. The system is intended to improve heat transfer. The mechanism of magnetic fluid treatment remains debated, which is why each result is assessed on the building’s own meter readings. Read how it is installed and measured.

Book a call

15 minutes.
That’s all it takes to find out.

Tell us about your building and we’ll talk through your site, your spend and whether it is a fit. If it’s not for you, no problem at all.

Pick a time in Jake’s calendar (opens in a new tab)
Jake Loggie, Business Development Consultant at V1 Energy Solutions

Jake LoggieBusiness Development Consultant, V1 Energy Solutions. Jake runs the 15 minute calls.

Prefer to talk now? Call Harry on +44 7871 000066 or email Harry@v1-energy.com.

Rather we called you? Leave your details and Jake will arrange a time.

The spend from the calculator is sent with your details: £150,000 a year.

We aim to reply within one working day.

We use your details to respond to your enquiry and arrange any survey or project you request. Read our privacy policy.